DSE 6120 Installation Instructions
Hide thumbs
Also See for DSE 6120:
- Installation manual
Advertisement
Quick Links
Typical Wiring Diagram
053-060
D E E P S E A E L E C T R O N I C S
ISSUE 1
DSE6120 Installation Instructions
ACCESSING THE FRONT PANEL EDITOR (FPE)
The module must be in STOP mode with the engine at rest before configuration mode can be accessed.
To enter the 'configuration mode' press both the INFO
ENTERING THE CONFIGURATION EDITOR PIN NUMBER
If the module PIN number has been set, the PIN number request is then shown. The configuration
cannot be viewed or changed until the PIN number is correctly entered.
•
The first * is flashing. Press + or – buttons to adjust it to the correct value for the first digit of
the PIN number.
•
Press
when the first digit is correctly entered.
•
The entered digit will turn back to a * to maintain security.
•
Enter the remaining digits of the pin number using the same method.
If the Configuration PIN has been entered successfully (or the PIN number has not been set in the module) the first
configurable parameter is displayed.
NOTE:- When
is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is not
correct, the editor is automatically exited. To retry you must re-enter the editor as described above
EDITING A PARAMETER
Enter the editor as described above.
•
Press
to select the required 'page' as detailed below.
•
Press
(+) to select the next parameter or
•
When viewing the parameter to be changed, press the
•
Press
(+) or
(-) to adjust the value to the required setting.
•
Press
( ) the save the current value, the value ceases flashing.
•
Press and hold the
( ) button to exit the editor.
.
Values representing pressure will be displayed in Bar. Values representing temperature are displayed in
NOTE: -
degrees Celsius
.
NOTE: - When the editor is visible, it is exited after 5 minutes of inactivity to ensure security.
NOTE:- To exit the front panel configuration editor at any time, press and hold the
have saved any changes you have made by pressing the
NOTE:- The PIN number is automatically reset when the editor is exited (manually or automatically) to ensure
security.
Deep Sea Electronics Plc.
Deep Sea Electronics inc.
Tel:+44 (0)1723 890099
Phone: +1 (815) 316-8706
Fax: +44 (0)1723 893303
Fax: +1 (815) 316- 8708
LO CALL (from UK BT landlines)
TOLL FREE (USA only) :
Telephone 0845 260 8933
Tel: 1 866 636 9703
Email: support@deepseaplc.com
Email: dsesales@deepseausa.com
Web: www.deepseaplc.com
Web: www.deepseausa.com
and STOP
buttons together.
.
(-) to select the previous parameter within the current page.
( ) button. The value begins to flash.
( ) button. Ensure you
button first.
Deep Sea Electronics Plc.
(Far East)
Tel:+66 2 670 6228
Fax: +66 2 678 3028
Email: support@deepseaplc.com
Web: www.deepseaplc.com
Advertisement
Related Manuals for DSE DSE 6120
Summary of Contents for DSE DSE 6120
- Page 1 Typical Wiring Diagram 053-060 D E E P S E A E L E C T R O N I C S ISSUE 1 DSE6120 Installation Instructions ACCESSING THE FRONT PANEL EDITOR (FPE) The module must be in STOP mode with the engine at rest before configuration mode can be accessed. To enter the ‘configuration mode’...
- Page 2 ADJUSTABLE PARAMETERS (Configuration editor) ront Panel Configuration Editor (Factory default settings are shown in bold italicised text) (Factory default settings are shown in bold italicised text) Section Parameter as shown on display Values Section Parameter as shown on display Values MAINS Voltage Low Trip 50V –...